FRenewable heat energy from Atmospheric Electron beam

FRIPROEnergy, LLC

Atmospheric Fueled Electron Particle Beam (AEPB)^{tm
c}& Combustion free Electronic Flame^{tm
c} heat source.

Also our new Product, Plant Plasma Growth Solution ^{tm c} for Growerss at PLANT PLASMA GROWTH SOLUTION 2012 |

Fripro Energy is an LLC of Ohio. Thomas Edward Fairbairn, Inventor-CEO US PATENT DETAILED 20100043729 Terrence J. Sherman-President and Director of Marketing

Note: This is a Color Brochure on line site for technical minded persons. Fripro is introducing a new electron particle beam generated Electronic Flame^TM
C, non-combustion heat source. This energy source (AEPB) runs on atmospheric air, and electrical inputs from any source including wind turbine generators, solar cells arrays, or the Electrical Grid. Other gases, liquids or powdered solids can be introduced for synergistic reactions.

Video #1 demonstrates the operation of the Electronic Flame driven by our AEPB on Atmospheric air

Note: One cannot see any carbon black or soot on the brick! The Electronic Flame^TM
C (photo) has no temperature when aimed directly into our atmosphere as measured by independent observers. Only when a ceramic target, Brick etc. is added the temperature goes off scale beyond the test observers temperature meter.

Both the electrical input and the Electronic Flame are additive in energy output from the brick target and the air heating Electronic Flame^TM
C. The Fire brick target also stores the heat energy generated for short period of time depending on the surrounding atmosphere, or any enclosure.

Video #2 Shows the (AEPB) as a Electron Particle Beam aimed into a enclosed Zirconium cylinder can be used for boilers, heating, water heaters, cooking stoves, greenhouses heating and pin point beam welding of very high melting point ceramics. The zirconium welding weld seam in the zirconium cylinder is a clear material, so far not identified.

Video #2 demonstrates a non-nuclear radiation energy heat source measured in (eV) volts with an end closed ceramic Zirconium cylinder. When the AEPB Beamenters the cylinder it drags atmospheric air and the air becomes additive to the ceramics cylinder's heat radiation.

Refer to page_2 for simplified text of our technology.

For detailed technical data, please continue on this page:

The introduction of fossil fuels to the AEPB can give a synergistic additive-thus as and possible cleanup of the present combustion fuels like oil, gas, wood and trash. So we do not have to give up our present pollution producing fuels, when using the AEPB technology! The soot and other pollutants i.e. methane can be removed or converted to safer molecules.

Photo #2a

Many combustion flame pollution outputs are avoided in the operation of the AEPB a non-vacuum Atmospheric Electron Particle Beam Generator. Again note in photo Photo #2a the brick is clean! No carbon residue!

When the compressed air pressure (SCFH) flow is increased the Electronic Flame^c tm gets hotter on the ceramic target a non-electrical (electron) conductor. However research indicates that the boiling fire brick's molecules may conduct the modulated electron beam further into the brick's surface area thus extending the area of melt and heating!

Refer to the ELECTROMAGNETIC SPECTRUM CHART for input and output range ((between 10^-8 (eV) to +10⁺² (eV) = 10¹⁰ (eV) a rise of 10¹⁰ (eV) input to output of the flame on the target)).

Ceramic's radiation output at 10² (eV) is where Infra red to UV is the positioned (of the heated fire brick) flame energy heating,

On the EMS Chart: The Photon one electron volt (eV) energy X axis located at the charts bottom. Then refering to the chart at: SOURCES designated RF cavity where our transformer input AEPB's electron beam to the target is at 10^-8 (eV).

Then view infra red, light and UV on the ELECTROMAGNETIC SPECTRUM CHART chart, Photo 2a COMMON NAME OF WAVES at 10⁺² (eV) is the above target brick's output point in radiation (heat energy) output.

Toggle full screen for best view, or F11 for the Video # 1. Refresh browser F5 often for latest data

The block diagram is shown below of the interconnections of the operating system of our product:

Please continue for detailed technical data on this page: or refer to page_2 for simplified technology.

Our non technical friends might ask how do we know if your companies Electronic Flame shown in Video #1 might not be burning a natural type gas?

Proving otherwise In the Video #1 the copper electrode is still copper color and is therefore at room temperature. If gas or any other combustion fuel were emitted in a combustion flame the nozzle would soon be black and so would the fire brick. In the Video #1 and the Photo 2a above the brick is clean!

If the reader views the operating copper nozzle closely in Video #1 above, one can time from start of the flame to viewing the red hot area in the 2,500 F fire brick surface and they will see it is red hot (1200 F degrees PLUS) in real time in less then 12 seconds on less then 4KW! Yet copper melts at about 1700 Degrees F and the fire brick melts (Boils) over 2700 Degrees F!

When the compressed air was increased the fire brick's temperature rose in about 40 seconds to boiling liquid! Refer to Photo #2a (the actual fire brick targeted in Video #1 above).

VIDEO #2b Human hand insertion test into AEPB beam (non-edited video and sound)

Excellent demonstration of the vertical AEPB in action into the atmosphere, with out a target electrical return circuit. Note different reactions to thick gloved, latex and bare hand when the electrical sensation of shock is demonstrated!

Note that high particle pulse rate of the AEPB is a surface reaction on the human hand.

Both VIDEO #1 and VIDEO #2 above operates in either an electron particle beam or flame form. Thus generating INFRA RED TO ULTRA VIOLET RADIATION flame and/or electron beam ENERGY.

Refer to: US PATENT 20100043729 (Includes the patent's Front Page, Page Images, Description of Claims).

FRIPRO Energy, LLC is again approved for $1,500,000 Investment Tax incentive (State Of Ohio) well into the year 2012. Refer to Page_3

Our AEPB technologies can be utilized by you’re own research and development teams, and will contribute to you're solving technical, operational problems or development of new energy efficient products.

Video #3 This an amazing lab test video and sound of the Fairbairn-Sherman Effect when throwing powered

sugar into the AEPB's Electronic Flame^C-TM. The light explosions can mostly be seen by the Video Camera and last for

about a milli second the human eye hardly catch the light blasts, as you can see a staff member walking right by it and not noticing it.

The voice of the camera man (test scientist) is heard he did see as he was looking directly at it. Refer to three inch Coal lump Photo #7

is white hot, no smoke or soot!

HYPERLINK METHANE Gas input to AEPB nozzle Video prior to adding AEPB ENERGY. Note deposits of carbon on target brick.

PHOTO #4 BELOW AFTER ADDING AEPB Electron Volt energy to the Methane Gas

PHOTO #4 METHANE GAS AFTER, via our air nozzle, AEPB ENERGY TO FIRE BRICK TARGET SHOWN IN THE ABOVE, and this HYPERLINK (METHANE Video). No carbon or soot IN THE Beam's AREA OF COVERAGE ON TARGET BRICK in the above photo -- Obvious increase in the energy to the target ceramic directed at the fire brick target. (Synergy in action)
Refer to ABC news reference article on Methane and Soot in the atmosphere:
http://abcnews.go.com/Technology/wireStory/scientists-cut-soot-methane-curb-warming-15348267?page=2

In the AEPB generator particle electron output the radio frequency generator operates at about 13.56 Mhz, at 5000 + watts. When the particle electrons hits the atmosphere or a target ceramic it ups it wavelength to the electron (particle) beam position on the electromagnetic Chart (Click on Hyperlink) Electromagnetic Spectrum Chart
Electrons can absorb energy from external sources, such as lasers, arc-discharge lamps, tungsten-halogen bulbs, (AEPB ) fluid enclosed electron beam in the atmosphere, and be promoted to higher energy levels. The photon energy or electron energy is absorbed by an electron or electrons to elevate it into a higher energy level.
Once it gives up its energy to a target the energy can subsequently be released, when the electron falls back to the original ground state, in the form of a lower energy photon. However the target ceramic preferred material stores the higher energy according to its input energy position shown on the Electromagnetic Spectrum Chart

Photo #6 Below Using CO₂ on sand stone in the AEPB
Nozzle at 1 SCFH mixed with fluid gas sheath at 2 SCFH gas

Photo #7 Below. White hot chunk of coal 6 sec. within the Electronic Flame, no smoke!

Photo #7 Above three inch chunk of high sulfur coal in the electronic flame in ten seconds glows smoke free white hot.

IF THE LUMP OF COAL shown in Photo #7 above IS LEFT LONGER IN THE ELECTRONIC FLAME IT WILL TURN DARK GLASS-LIKE IN THE AREA OF THE FLAME CONTACT. FRIPRO ENERGY CALLS IT COAL GLASS!

The Hypothetical formula for Mass to radiation in the AEPB is:

Mass = K_f Nu    Nu being frequency, or when convert to electron volts (eV)

K_fis the Ether constant in space. Mass is in grams. The higher the Mass in grams of the electron wave front the higher the impact energy on its target. Its position is indicated in the ELECTROMAGNETIC SPECTRUM CHART . The electromagnetic wave front has an equivalent mass in grams and can be converted to electron volts (eV).

           Refer to page_2 for simplified text of our technology.

            Details are very well shown in the US PATENT APP. 20100043729 Hyperlink

(This copy of the patent Includes its Front Page, Page Images, Description and Claims). Filed in 2008, 2009 and published 2010. Also filed internationality.

Fripro Energy, LLC's (CEO) filed both first and invented first--with respect to the new patent law of the USA! Now assigned to Fripro Energy, LLC.

Photo #5 Hyperlink Photo AEPB generated Volcanic glass carbon in Sandstone

Volcanic glass carbon in Sandstone click on this hyperlink for a clearer blowup of boiling sandstone bubble

Photo #5 above Using Propane gas plus the AEPB on sand stone in the AEPB Nozzle at 2 SCFH gas, temperatures in the thousands degrees F were generated.

Note: Estimate of one million glass like balls per square inch.

Sandstone shows the effect the AEPB and Propane (C₃H₈) has on the sandstone target, thus creating the black glass shown in the photo #5 above. Also in on line Movie and sound (click) Volcanic glass carbon in Sandstone (Magnification view, click on photo)

Note: Without the injection of the gases, the sandstone is nearly clear glass with possibly Si and other molecular mixtures as the sandstone is not clean sand.

Lower gas or powdered coal usage with atmospheric compressed air in the AEPB, stretches the gas or coal supply availability, lowers their price, with nearly little output stack emissions depending on power and applied conditions.

The AEPB's (electron particle beam) ability, through synergism, can in certain conditions, capture/store a carbon residue (CCS) from propane, natural gas, powdered coal, all injected within the AEPB and its generated Electronic Flame^c tm.

Photo #6 top left. Sandstone photo shows less than one SCFH of CO₂ introduced to the AEPB Beam nozzle an atmospheric electron beam on the target. The amount of carbon deposition, which may or may not be in the sandstone pictured in the photo to the right, is very small because of the supply at less than 1 SCFH of CO₂

The target and beam were as bright as the sun and required very dark glasses to view. Time on target less than 10 seconds!

CO₂ is also part of the atmosphere therefore in a sense a fuel for the AEPB, has already been realized. Refer to Video # 8 below.

This is very important as combustion stack emissions (soot) can be stored and rerouted back through the AEPB Generator, producing added energy that would be lost to the atmosphere through chemical combustion.

To understand how the AEPB Generator operates, apply this logic:

When energy units are separately employed on a target, one unit of energy (called an electron particle energy) and one unit of chemical energy identified as fluid energy (propane gas plus Oxygen C₃H₈ + O, or water H₂+O) is utilized in the following manner:

VERSES:

When one electron energy unit and one fluid energy unit are combined through the AEPB nozzle's fluid sheath at the same target, the formula is now 1 electron energy unit + 1 fluid energy unit = synergistically added energy units applied at the target.

This combination of energy units is called Synergism.

One AEPB unit of energy may have more energy then one chemical combustion Fluid unit of energy. (Energy units employed are variable).